• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged window pane can be a nuisance. This could be an opportunity to upgrade your windows to energy efficient or insulated ones, and reap benefits like increased comfort, increased resale values and reduced utility costs.

You can do it yourself for only a fraction of the cost it would cost to employ an expert. You'll only require the proper tools and a few hours of your time.

Glass

If your single-pane windows are old broken, deteriorating or damaged, replacing them with newer glass that is tempered or insulated can increase energy efficiency and decrease noise while also preserving the historic integrity of older homes. A majority of homeowners with hand tools can replace Window pane the window pane. You will also need an additional window pane, glazier's tips, pliers, and latex glaze putty. If needed, you can make use of a heat gun to warm the old putty. Wear safety glasses and gloves prior to starting. Working with broken glass could result in serious injuries.

Begin by removing any remaining broken pieces of glass. It is best to use pliers for this however a flathead could work equally. Use a wood chisel, or putty knives, to take away any remaining old putty around the frame and the window sash. Be careful not to damage the window sash. Be careful and slow. This is best done on a ladder, not on the ground. Also, Replace window pane ensure that someone lower to ensure it is held steady.

After you've removed all the old putty, Replace Window pane you can prepare the window frame for the new pane. Find the width and the height of the sash opening and subtract 1/8 inch from each measurement (to allow for seasonal expansion and contraction). These measurements can be taken to a home center or hardware store to have an item cut from glass that is in stock to the correct size. You can cut the glass yourself if you possess the right tools.

After putting the new pane in place after installing the new pane, put a tiny amount of caulking along the edge to make it weatherproof. Install a glazier’s point on both sides of the frame. This will secure the pane. The points shouldn't be too tight that they create friction between the frame and the sash However, they should not be loose.

Before putting the putty on, knead it thoroughly until it's soft and free of lumps. Make it into pencil-sized strips. Apply the first strip to the corner of the frame. Work from corner to corner, making sure it is even and smooth.

Glazier's Points

The glazier's points are the small triangular pieces which help to secure glass into a window frame without scratching or damaging the fragile surface. It's easy to understand how to use this hidden tool and you can save money on the expense of a professional installation.

After taking off the old putty, glazier points as well as any remaining remnants, clean the frame thoroughly with an utility knife. If needed, lightly sand the wood along the grooves of the rabbets to smooth rough spots. If you do sand your wood, be sure to protect it by using painter's tape to prevent accidental damage.

Measure the empty frame's dimensions and write down accurate measurements. Bring these measurements to an hardware store or home center, and have the new pane cut slightly smaller than the frame's opening. This will ensure that the pane fits perfectly and allows for expansion and contraction.

Place the new window in the frame and push it in place by using your hands. Then use the point of your chisel, or the back of the putty knife to pierce the glazier's points as illustrated in Figure 11. The glazier's point should be aligned with the top edge of the pane and the shoulders should be just below the lip.

Apply a thin bead of glazing compound on the edges of the new glass and into the rabbet grooves, to seal and protect them. Allow it to dry completely and cure.

Install the new window sash after the glazing compound has dried. First, coat the wood with a heavy coat of linseed oil. This will stop the new putty drying out or cracking as it absorbs moisture. Apply the coating using a brush this coat, or the point of the blade. Then, use the chisel that is on the back of the tool or the back of the putty handle to gently hammer the new sash or glazier's point into the grooves of the rabbet. Repeat this process at intervals of 10 inches around the frame.

Putty

A baseball thrown or a rock thrown by error, or a fallen tree can cause a broken or cracked window pane. Luckily, most windows can be repaired by simply placing a new piece in the right place. The glass is held into place by a small metal clip, also known as a glazier’s point and putty. This compound is also known as glazing compound. Remove the old pane and clean the area with a rag, a pull-type scraper, or a wood chisel. Wear safety glasses and gloves while working. If the window is glued to the frame, you'll need make use of a heat gun to soften the adhesive before cutting it loose.

If you're planning to install the original sash, remove the molding pieces that secure the old pane. Sand the sash until it's flat and ready to receive new caulk. Once the sash is re-installed and sanded, apply a fresh silicone caulk around the glass to ensure that it won't leak or discolor in time.

Take the glazing points out of the rabbets, the grooves in the sash that the glass is. If they are hard to cut, place a hand tool like a heat gun over them to allow them to soften before. If you're using a heating gun, make sure not to cause damage to the sash or its railings by placing the tool too tightly.

Make a bed for your new pane by removing the old glaze points and putty. Roll a piece of glazing compound between your hands, shaping it to be around 1/2-inch thick. Press it into the rabbets, where the glass will be placed. It is essential that the glass is positioned against the putty in all places on both sides If you have to tap it, gently press the glass into the rabbet using your thumb.

If the new pane has a crack then you can seal it with a solvent-based glue or silicone caulk before pressing it into the sash. If the crack isn't sealed, you'll require putty to keep the water out. Once the putty is dry, wipe the oily film from the glass and allow it to dry completely before painting. Paint before the putty has completely dried. It will not form a good seal and may leak or discolor with time.

Paint

If you've suffered a break in a window pane, then you may be concerned about the expense of a new one. However, replacing a single glass pane doesn't need to cost a fortune when you do it yourself. Even a double glazing replacement windows-paned window can be replaced for a fraction of what it would cost for a professional.

First, if you're working on a large-sized window, ensure that it is securely fixed to the frame. This can be made relatively simple and quick with the right tools and techniques.

If you're ready to begin taking off the old window by prying out the glazing points of metal that are attached to it. These are tiny metal triangles that act as "nails", holding the window in place. They are submerged beneath a glaze putty or bead which hardens into solid wedge that holds the wood frame firmly in position and conceals the edges.

After you have removed the old pane taken away Clean up the frame and wood. Scrape away any paint and sand down the rabbet grooves, where the glazing points used to be. Sand them down to bare wooden surfaces so you can paint the frames the same color. After sanding the wood, apply a layer of flax oil. This will help to extend its life.

Next, measure the dimensions of the window opening. It is necessary to take vertical and horizontal measurements of the entire opening, as well as the thickness of the old pane. To get the exact size of the new pane, subtract 1/8 inch from both measurements. This will also allow for expansion and contraction of the glass in times of seasonal changes. You can bring these measurements to a hardware or home improvement store and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.