• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace window pane Window Panes

A damaged window pane can be an inconvenience. It could be a chance to upgrade to energy-efficient windows or insulated ones and enjoy advantages like improved comfort, increased resale values and reduced utility costs.

This is a project you could take on yourself for only a fraction of the cost of hiring an expert. You only need the appropriate tools and a few minutes of your time.

Glass

If your single pane windows are old damaged, cracked or deteriorating, replacing them with newer glass that is tempered or insulated will increase energy efficiency and decrease noise while maintaining the historic integrity of older homes. The procedure of replacing a window pane is relatively easy and can be completed by most homeowners who possess basic hand tools. In addition to a replacement pane, the following components are needed for the replacement process: latex glazing putty pliers, glazier's points and an electric heater to warm the old putty, if needed. Before beginning, wear protective gloves and goggles since working with broken glass can cause injuries.

Remove any broken glass pieces that remain. It is recommended to use pliers for this however a flathead could be useful as well. Utilize a wood chisel or putty knives, to take away any old putty remaining around the frame and the window sash. Be careful to not damage the window sash. Be careful and slow. This should be done on a ladder, not the ground. Also, have someone lower to ensure it is held steady.

After you've removed all the old putty, you can prepare the window frame to fit the new pane. Take measurements of the width and height of the sash opening and subtract 1/8 inch from each measurement (to allow for replace Window pane seasonal expansion and contraction). These measurements can be taken to a hardware or home center store to get cut a piece of glass stock to the proper size. Alternately, you can cut the glass yourself if you have the appropriate tools.

After installing the new pane After installing the new pane, apply a small amount of caulking around the edges to make it weatherproof. Install a glazier's pointing on both sides of the frame. This will help secure the pane. The points should not be so tight that they cause friction between the frame and sash however they should not be loose.

Before applying the putty knead it thoroughly until it's soft and free of lumps. Cut it into pencil-sized pieces. Place the first strip in the corner of the frame, moving from one corner to the next so that it is smooth and even.

Glazier's Points

The glazier's points are the small triangular pieces of metal that allow glass to be secured into frames for windows without damaging or scratching the delicate surface. Knowing how to use these hidden tiny pieces of help is simple and could save you money on professional installation or the cost of new glass.

After the old putty as well as the glazier's points have been removed, replace window pane thoroughly clean the frame with a knife to eliminate any remaining traces. If necessary you can lightly sand the wood in the rabbet grooves to smooth rough spots. If you do sand your wood, be sure to protect it with painter's tack to avoid accidental damage.

Take measurements of the empty frame and record precise measurements. These measurements can be brought to the hardware or home center store and the new pane will be cut slightly smaller. This will ensure a tight fit, and allow for expansion and contraction.

Place the new pane into the frame and push it in using your hands. Then, you can use the point of your chisel or the back of the putty knife to pierce the glazier's points as shown in Figure 11. When you're done, they should be flush with the top edge of the pane. the raised shoulders of the points should be just below the rabbet's lip. groove.

Apply a thin layer of glazing compound to the rabbet grooves and edges of new glass. This will protect and seal the edges. Let it dry completely and cure.

When the glazing compound is dry it's time to put in the new window sash. First, saturate the wood with a heavy coat of Linseed oil. This will prevent the new putty from taking up moisture and drying out and cracking with time. Apply the coating using a brush this coat, or the point of the putty blade. Then, use the chisel on the back of the tool or the back of the putty handle to gently smash the new sash or glazier's point into rabbet grooves. Repeat this process in intervals of 10 inches all around the frame.

Putty

A baseball hit or a rock thrown in error, or a fallen tree can cause a broken or cracked window. The majority of windows can be repaired easily by simply putting in a fresh piece. The glass is held in position by a small metal clip, referred to as a glazier’s point and putty. This compound is also called glazing compound. Remove the old pane and clean the area with an abrasive, scraper that is a pull type or a wood chisel. Wear protective glasses and gloves while working. If the window is secured to the frame, you'll have to employ a heat gun in order to soften the adhesive prior to prying it free.

If you plan to reinstall the original sash, gently remove the molding pieces that secure the old pane. Then, sand the sash to ensure it's level and ready to be re-caulked. After the sash has been installed it is possible to apply a silicone caulk over the glass. This will ensure that it won't be leaking or fade over time.

Remove the glazing points from the rabbets, the grooves in the sash, where the glass sits. If they're difficult to cut out, try holding the hand tool, such as a heat gun over them to soften them up first. If you're using a heated gun, make sure not to damage the railings or sash by holding the tool too closely.

Once the old glaze points and putty are removed, prepare a bed for the new pane. Roll a rope of glazing compound between your hands, and form it into a 1/2-inch thick. Then, you can press it into the rabbets, where the glass will rest. It is essential that the glass sits on the putty on each side If you have to tap it, gently press the glass into the rabbet using your thumb.

If the new pane has a crack, you can cover it with a solvent-based glass glue or silicone caulk prior to pressing it into the sash. If the crack isn't sealed, you'll need to use putty to keep the water out. Once the putty is dry clean the oily film from the glass and let it dry completely before you paint. If you paint before the putty is fully dry, it won't form an effective seal and could leak or discolor over time.

Paint

You may be concerned about replacing a broken piece of glass. The truth is, replacing a single pane of glass doesn't need to be expensive if you do it on your own. In fact windows with double panes can be replaced for only a fraction of the cost of a professional.

First, if you're working on a large window, ensure that it is securely attached to the frame. By using the correct tools and techniques you can complete this task easily and speedy.

When you are ready to begin taking down the old window pane. Take out the glazing points made of metal that are attached to it. These are small metal triangles that function as "nails", holding the window in place. They are buried under a bead of glazing putty, which transforms into a solid moulded wedge which holds the window in place and hides the edges.

After removal of the old pane clean the frame and wood. Scrape off any paint that has been used and sand down the rabbet grooves that the glazing points were placed. These should be sanded down to the point of being bare, so that you can paint them the same shade as the rest of the frame. After sanding the wood then apply a layer of flax oil. This will help to prolong the life of the frame.

Then, you need to measure the size of the window opening. It is necessary to take vertical and horizontal measurements of the entire opening, Window Replacement as well as the thickness of the old pane. Subtract 1/8 inch from each measurement to ensure that you get a precise size for the new pane. This will allow for seasonal changes in the glass. You can bring these measurements to a hardware or home improvement shop and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.