• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace window pane (www.themcwars.org) Window Panes

A damaged window pane could cause a lot of trouble. It could be a chance to upgrade to energy-efficient windows or replace window Pane insulated ones to enjoy benefits such as improved comfort, higher resale value and reduced utility bills.

It's a project you can do yourself for less than the cost of hiring a professional. You'll only require the right tools and a few hours of your time.

Glass

If your single-pane windows are outdated broken, deteriorating or damaged replacing them with more modern insulated or tempered glass can increase energy efficiency and reduce noise while preserving the original character of older homes. The procedure of replacing a window pane is relatively simple and can be done by homeowners with basic hand tools. You will also require a replacement window pane, glazier's tips, pliers, and latex glaze putty. If needed you may use a heatgun to warm the old putty. Before beginning, wear protective gloves and goggles since working with broken glass may cause injuries.

Begin by removing any remaining broken pieces of glass. This is best accomplished with a pair of pliers, however, a flathead screwdriver can also be used in a pinch. Then, use a wood chisel or putty knife remove the remaining old putty around the frame and the sash. Be careful to not break the window sash. Take your time and work slowly. It is recommended to work on a stable ladder rather than on the ground and have someone stand below the sash in order to help hold it steady.

Prepare the window frame to accommodate the new pane once you have removed the old putty. To allow for seasonal expansion or contraction and contraction, subtract 1/8 inch from the measurements of the width and height. These measurements can be sent to a hardware or home center store to have an item cut from glass stock to the proper size. You can also cut the glass yourself if you have the right tools.

After putting in the new glass, apply some caulking around the edge. This will make the glass weatherproof. Then, you can install a glazier's pointing on the frame's opposite side to hold the pane in the right place. The points shouldn't be so tight as to cause friction between the frame and sash but they should not be too loose.

Before applying the putty, work it in a gentle manner until it is soft and free of lumps. Roll it into pencil-sized strips. Apply the first strip to the frame's corner. Work from corner to corner, making sure it is even and smooth.

Glazier's Points

The glazier's points are small triangular pieces of metal that allow glass to be secured into frames for windows without scratching or damaging the delicate surface. Learning how to use these little helpers is easy and could save you money on a professional installation or the cost of buying new glass.

Once the old putty and the glazier's point are gone Clean the frame thoroughly with a knife to eliminate any remaining traces. If needed you can lightly sand the wood along the grooves of the rabbet to smooth out rough spots. If you sand wood cover it with painter's tape to avoid accidental damage.

Write down the exact dimensions of the frame. These measurements can be brought to an hardware or home centers store, and the new pane will be cut slightly smaller. This will ensure a secure fit and will allow room for expansion and contraction.

Place the new pane into the frame and press it in place with your hand. Use the point of the chisel, or the back of the putty blade to tap the glazier's points, as illustrated in Figure 11. The glazier's points should sit in line with the top edge of your pane and the shoulders should be just beneath that lip.

Apply a thin layer of glazing compound to the rabbet grooves as well as the edges of the glass. This will seal and protect the edges. Allow this to dry and cure completely.

After the glazing compound dries and the glazing compound is dry, you can install the new window sash. The first step is to coat the wood with a thick layer of linseed. This will stop the new putty from drying out and cracking due to the moisture it absorbs. Apply the coat using a brush or the tip of your putty knife, then use the chisel or the back end of the knife to gently hammer the new sash and glazier's tips into the grooves of the rabbet. Repeat this process every 10 inches around the frame's perimeter.

Putty

A baseball that is thrown or a rock that is errant or falling branch could cause a window to break or crack. Fortunately, windows can be easily replaced by simply placing a new piece in place. The glass is held in place using a small metal clip called a glazier's point and putty, often called glazing compound. Before you install a new pane, first get rid of the old one and clean up the area with the help of a rag, the pull-type paint scraper or the wood chisel. Wear safety glasses and gloves while working. You'll need a heating gun if the window is glued to the frame.

If you plan to reinstall the original sash, remove any pieces of molding that secure the old pane. Then you can sand the sash down to ensure it's level and ready to be re-caulked. Once the sash is re-installed and sanded, apply a fresh silicone caulk around the glass to ensure it doesn't swell or fade as time passes.

Remove the glazing points from the rabbets and the grooves in the sash, where the glass sits. If they're difficult to cut out, try holding an instrument like a heat gun to soften them before you do. When using a heat tool, be sure to not damage the sash and its railings.

Make a bed for your new pane after removing the old glaze points and putty. Roll a rope of glazing compound between your hands, forming it into a 1/2-inch thick. Then, you can press it into the rabbets in which the glass will be. It is crucial that the glass is positioned against the putty in all places on each side If you have to do so, gently tap the glass into the rabbet with your thumb.

If the new pane has a crack you can fill it with a solvent-based glue or silicone caulk prior pressing it into the sash. If the crack is not sealed, you will need to apply putty to keep the water out. After the putty has dried clean the oily film from the glass and allow it to dry completely before painting. Paint after the putty has dried completely. It won't create a solid seal and may leak or discolor replace Window pane with time.

Paint

You may be concerned about replacing a broken pane of glass. It's true that replacing a single pane glass doesn't have to be costly even if you do it your own. Even a double glazed replacement windows-paned window can be replaced for a fraction of the price it will cost a professional.

If you are working on a large window, ensure that it is securely fastened to the frame. This job can be made relatively simple and fast with the right tools and techniques.

If you're ready to begin with the removal of the old window pane by removing the glazing points made of metal that are attached to it. They are basically tiny metal triangles that act as "nails" that hold the window in place within the frame of wood. They are placed under a glaze putty or bead that hardens to an unbreakable wedge that holds the wood frame in place and hides the sharp edges.

After removal of the old pane clean the frame and the wood. Scrape away any old paint and sand down the rabbet grooves, where the double glazing replacement window points were. Sand them down to bare wooden surfaces, allowing you to paint the frames the same shade. After sanding, apply a coat of flax oil on the wood's surface to help extend its lifespan.

Next, measure the dimensions of the window's opening. It is necessary to measure the horizontal and vertical dimensions of the entire opening, as well as the thickness. To get the exact size of the new pane, subtract 1/8 inch from both measurements. This will allow for seasonal changes in the glass. Take these measurements to your local hardware or home improvement store, and they will have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.