• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen can maneuver large glass panes from a high point above the ground. They adhere to strict safety standards and are often working in harsh weather conditions.

Wearing protective clothing, remove all glazing putty and glazing points using a knife. A heat gun may help soften the old putty and make it easier to remove.

Replacement

When a window's pane is broken, it may be tempting to try and repair the glass rather than replace it. However, replacing windows is typically more cost-effective, and can also assist in preventing other issues that could affect your home's energy efficiency. It is also important to consider the type of glass that's broken to determine if it is an interim fix or if you will require an alternative that is more durable.

To fix a damaged window, remove the sash or frame and place it flat on your work surface. Wearing eye protection, gently wiggle the window's frame and remove any remaining fragments. Then, use a knife to remove the glazing compound and glazing points that keep the glass in the position. Keep the track of the components and their locations so they can be reinstalled.

After you've removed the frame and sash, you can begin preparing to replace the glass. Make sure that the opening of the frame is the right size for your replacement window. To allow for the expansion of the frame and glass and contraction to both directions, measure the opening and subtract 1/8 inch. Afterwards, purchase double-strength glass cut to these exact measurements. It is also recommended to purchase enough new glazier's clips or glazier's points to be positioned every 6 inches around the window pane.

If the manufacturer is accountable then you should call them and make an claim. Once the new glass is installed, it needs to be bedded in with a thin coating of glazier's compound. After drying the compound and dry, you can paint it to match the frame of the window.

If your crack is more than an inch you can stop it from expanding by slicing an arc that is just a little beyond the crack. This technique isn't 100% foolproof but it can slow the growth of the cracked until you are able to take permanent measures.

Repair

Professional window contractors are trained to handle a variety of glass, and they have the tools to do the job correctly. They also know the best methods for disposing of waste, and are less likely to leave crumbs in the trash, which could cause harm to pets or family members. They're also accustomed to working with different window types, and they may be aware of issues that aren't obvious to the uninitiated homeowner.

Before you begin the process of repairing cracked window glass, make sure to wear safety goggles and gloves. A small crack can cause shards to fly, posing a danger to anyone in or around the home. It is crucial to determine what caused the crack, so that you could prevent future problems.

Begin by creating a two-part epoxy mixture. These are usually 50/50 mixture of hardener and resin, and must be mixed quickly. After the mix has been made then apply it directly to the crack and allow it to dry. It will take just some minutes, but it's essential to do it quickly because the mixture is very thick and quick drying.

After the epoxy has dried, you can take off excess epoxy with a blade. Then, you'll need to clean the area around the crack of glass. If you don't clean it correctly, the residue could cause further damage to the glass. After the glass has been cleaned, use a putty knife to smooth the compound along the edge of the window, and then match it with the frame of wood.

For a more durable solution, consider using a plastic covering. A trash bag that is heavy-duty or tarp is the best option, but you can also use masking tape to cover the glass. This will keep the crack from expanding and will also block out water, wind bugs, debris, and water.

You can come up with an interim fix in the event that you are unable to reach the window in time. Apply a small amount silicone sealant around the edges of the broken glass. It won't seal the gap between the frame and glass completely but it will hold the break in place until you are able to repair it.

Repainting

Repainting old glass windows is a good idea. This is a cost-effective alternative to window replacement and it can give your home a new look. Make sure the window is clean before painting. Use rubbing alcohol or soap and water to wash away oil smudges, and other traces of dirt that can hinder paint from adhering. Wear rubber gloves while working on glass to avoid transferring your own oils onto the glass surface. Apply multiple thin coats instead of one thick coat. This will allow the paint to last longer and will keep your windows looking smooth and even.

Make sure you have the proper tools available in case you want to paint glass windows. You'll need a brush, sponge, painter's tape, toothpicks, a ruler as well as a few other tools such as a rag or paper towel. You should also have the paint and brushes you'll need for Glazier the project in your possession. Make sure you follow the manufacturer's directions and have plenty of patience as it can take awhile for the paint to dry.

It is also important to ensure that the space you're working is well ventilated, especially if you're using solvent-based paint. This will help to reduce the chance of inhaling toxic chemicals, and the paint will dry more quickly. Use a protective mask when using spray paints.

You'll need to clean the glass window thoroughly with soap and warm water before you paint it. Use soap and warm water to thoroughly clean the glass window. Then, rub alcohol on any oil or grease residues that could interfere with the paint's adhesion. Make sure the windows are dry prior to coating them.

If your glass windows are energy efficient dual pane windows, you might be able to make a claim with the window manufacturer or dealer that sold them to pay any repair or replacement costs. This is especially true if you have experienced several issues with broken glass or condensation even though the windows are covered by warranty.

Sealing

If you have double-pane windows that have a damaged seal or more recent insulated glass units (IGUs) that have experienced fogging or fog, there are many options to address the issue. The most expensive option is to replace the insulated unit and frame but it may be necessary if condensation or fog are causing energy loss. Other options include replacing the IGU with a single pane, or repairing the existing IGU by drilling a hole in the bottom and filling it with an anti-fogging agent.

You can also fill in the gap between the window frame and the threshold or sill with a felt strip or vinyl v-strip. Felt can be stapled, glued or placed in place, but does not offer much protection against moisture. Vinyl weather stripping v-strip is durable and easy to install, but it is costly and is usually reserved for areas that are exposed to high abrasion. Door sweeps can be easily nailed in place and are inexpensive. However, they offer only a small amount of protection between the threshold and air.

To fix a damaged window seal, use a putty blade to take off the caulk. Wearing eye protection and gloves take care to remove the glazing points -- tiny fasteners that hold the glass to the frame's recess with sharp and pointed edges. After removing the glazing points, remove the grooves and sand the wood. Clean any sanding dust, then seal the bare wood surface using a linseed oil-based paint or clear sealer.

A putty or caulking knife can be used to apply the traditional glazing putty, but the use of a knife allows for an easier application and a better seal. Select a putty made specifically for glass, as it will last longer and stick better.

Apply a thin layer of putty across the inside of the frame where it meets with the glass. Slide the window into the frame so that the cut line on the glass aligns with the frame's edge. Apply pressure on the glass to compress the putty and glass into a tight seal. Smooth the compound with a gloved hand and remove any caulk or drips that were not properly applied before it dries.