• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Properly Start a Wood Burning Stove

Wood stoves can be a great way to save energy and also heat the room. They require some care.

Many modern wood stoves conform to EPA emission guidelines. Look for an EPA sticker either under or on the grate to make sure your stove won't produce lots of harmful pollutants.

How to start a Wood Fire

The sound and smell of a wood fire can be a welcome addition to any house. It's essential to know how to build an effective fire on your stove. Incorrect methods can result in a fire that doesn't burn efficiently and creates creosote or smoke. The tips below will help you start the fire that will warm your home with minimum effort and with the highest security.

Before you begin a fire, check the condition of your coals and logs. If they are wet it will dampen your fire and prevent the proper burning. You might want to open the chimney to eliminate any ash that falls into the stove.

Begin by placing a few small, dry newspaper pieces in the stove. This will help ignite the tinder. When the tinder and the kindling have begun to burn, you can put an additional layer of larger pieces on the top. This should be done in a crosshatch pattern so there is air between each piece of wood burning stove outdoor.

If you have wood stoves that have an automatic combustion control that will automatically deliver a controlled stream of air to the flame as it heats. This will enable the fire to burn at a consistent pace without the need to open the stove's door to tend it.

Avoid using too much tinder as it will cause the fire to burn at a fast rate and not use the fuel effectively. If you have a solid bed of tinder and kindling in your stove, you can start the main fire by placing two large base logs across the grate. On the top of these base woods lay a layer parallel to them. This method of creating an ember called a "top-down" fire will result in an effective and long-lasting fire that does not overtake the larger base logs.

Close the damper after your fire has been established and kept it closed. Doing this too soon can cause the fire smother and will not allow for the correct airflow, which will reduce its efficiency.

Add Wood

Stoves can be used to heat your home efficiently and save you money. They can be used alone or together with central heating or furnace system to provide the additional heating required in large homes or homes with many rooms. Many of the new clean burning stoves that are available on the market use advanced combustion technology that can separate the burning volatile substances from combustible gasses and tar. This is accomplished by providing air at two different stages. The first stage allows the burning of volatile compounds and the second supplies fresh air that has been pre-heated. This improves the combustion process and helps reduce the smell.

The amount of heat you get from a stove will depend on the species and moisture content of the wood you use, and also the size of the logs. The logs should be stored in a well-ventilated area for several months before you attempt to burn them, to give the wood time to dry. If the logs contain excessive moisture, they'll produce steam which is essentially wasted energy.

You should add wood to the pile in intervals and not all at one time. Adding too much wood at one time can cause the temperature of the firebox to rise, and creates a vortex, which draws smoke and volatile compounds that have not been burned back into the flame which could reduce your stove's efficiency.

Avoid using other combustibles in your stove such as cardboard or paper, because they are not wood. They have different physical properties and are unable to be burned without creating dangerously high temperatures. It is not recommended to burn compressed combustibles such as wood briquettes since they are different in physical and chemical composition from firewood. They are also not type-approved to be burned in wood burning stoves.

If you are installing wood-burning stoves in your home, it is crucial to have it installed and tested by a qualified. A certified WETT technician can examine your stove to make sure it is safe and functional. They will also ensure that your chimney is functioning properly. These professionals offer maintenance services for your stove and chimney to ensure they are in good condition. They will look for leaks in the areas that are accessible to your chimney and repair any issues they spot. They will also make sure that all residents of the home understand and follow the evacuation procedure in case of an accident.

Adjusting the Damper

A damper controls the amount of heat that is lost through the chimney when you're not using your stove wood Burning. Additionally, it can help you control the fire. If the flue is open but the damper is not closed enough, the fire will not burn as efficiently and it will billow out smoke into your living space. To ensure you have the most effective fire using your damper set correctly, you should test different locations and observe how each affects the flames.

Typically, you want to keep the damper open enough to let air enter and out of the flue while the fire is burning. This will allow the fire to begin and remain lit for a number of hours. The proper opening will stop the fire from being starved of air and prevent it from blowing smoke.

In order to properly adjust your damper you need to ensure that the fireplace is heated and the wood stove is hot. This will ensure that the chimney stays warm and has an adequate draft. After that, the damper for wood stoves can be adjusted.

Once the fire has smolder for a while, you can close the damper to about three-quarters of its maximum. This will prevent warm air in the room from getting into the chimney, but still allowing smoke to escape.

This is the best way to keep the fire from getting too hot, while also keeping it burning. The draft could be stopped if one closes the damper too far but a cold wind could be able to enter your home when the damper is not closed.

By placing your hands on the top of the flue pipe will tell you how much the damper has opened. If you feel a slight breeze pushing on your hand it's likely to be in the open position.

The damper settings can vary from one stove to another and even among different types of wood. Experimenting with the various settings will give you an idea of what you should look for, but you will need to adjust it until you find the ideal setting for your stove.

Clean up

After a fire, it is essential to clean the stove and flue. This reduces the chance of an ensuing fire in the chimney which is the most common cause of fires caused by wood stoves. Creosote is a sticky substance that accumulates on the inside of the stovepipe and can be extremely hazardous. It is caused by the moisture and wood particles that are not burned that are unable to escape from the fire. It could be caused by improperly lit fires.

A regular cleaning schedule can help to prevent the buildup of creosote. The best way to do this is to sweep the chimney at least once a year. It is recommended to have your fireplace and stove professionally cleaned and inspected at least once per year, modern wood burning Stoves too.

It is also a good idea to clean out the Ash tray and grate frequently. It is best to burn only seasoned wood since it will create less creosote. It is also recommended to avoid burning paper, cardboard, plastic and other trash items. These items can release dangerous chemicals to the air and flue, which can be released into your home.

The glass that is used on the wood stove has to be regularly cleaned too. Many newer wood stoves have self-cleaning glass, meaning that they do not require much cleaning. If you're not able to get the glass on your wood stove as clean as you'd like, there are stove glass cleaners can be used on the window.

Other ways to maintain your wood stove include turning down the vent when you're not using it, and slamming doors or windows to allow more airflow. This keeps the fire burning more hot and efficiently. The wood stove won't have to perform as hard to circulate air. It is also a good idea not stack logs or keep them in the flame for long periods of time, as this can lead to splitting and warping. In addition, it is a good idea to avoid using compressed combustible wood logs in your wood stove as the paraffin they contain could melt and spill into the flue which could cause damage.