• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen work up above the ground, moving massive glass panes. They adhere to strict safety standards and frequently work in extreme weather conditions.

Wearing protective clothing, take off the glazing points made of metal and the glazing putty by using a utility knife. A heat gun can help soften the old putty and speed up removal.

Replacement

If a window pane breaks, it could be tempting to try and repair the glass rather than replace it. However, replacing windows is typically more cost-effective and may assist in preventing other issues that could affect your home's energy efficiency. Examine the kind of glass damaged to determine if it's a temporary fix, or if a more permanent solution is needed.

To fix a broken window, remove the frame or sash, and place it on the work surface. Wearing eye protection, gently wiggle the window pane and remove any remaining shards. Then, use a utility knife to cut off the glazing compound and points that hold the glass in place. Keep an eye on the components and where they are so they can be reinstalled.

Once the frame and sash have been removed then you can begin the process of preparing to install the new glass. Be sure to check that the opening of the frame is the proper size for your replacement window. To allow for the expansion of the frame and glass and contraction to both directions, measure the opening and subtract 1/8 inch. Afterwards, purchase double-strength glass cut to these exact measurements. It is recommended to also purchase enough glazier's clips, or points to place them every 6 inches around each window pane.

Based on the window's warranty it could be covered by the manufacturer, in which case you must contact them to file an claim. Once the new glass is installed, it should be covered with a thin coating of the compound used by glaziers. After the compound has dried then you can paint it to match the rest of the frame.

If you have a crack that extends more than an inch, cutting an arc of a razor blade just beyond the crack could help stop it from spreading further. This technique isn't 100% infallible, but it will slow the development of the crack to a manageable level until you are able to take more permanent measures.

Repair

Professional window installers are equipped with the proper tools and know how to work with various types of glass. They know how to dispose of waste safely and are therefore less likely than others to leave behind pieces of glass that could harm family pets or family members. They're also accustomed to working with different types of windows, and they may be capable of identifying issues that aren't apparent to the uninitiated homeowner.

Before you begin the process of repairing damaged window glass, make sure to wear safety goggles and gloves. A minor crack could cause shards of glass to fly away, creating a risk for anyone who lives in or around the home. It is also crucial to determine the cause of the crack in the first place, so that it can help prevent future issues.

Create a two-part mixture of epoxy. They are usually made up of a 50/50 mix of hardener and resin. They must be mixed quickly. Once the mixture is ready put it in the glass crack and let it dry. This should only take about a minute but it's important to do it quickly because the mixture is extremely thick and quick drying.

Once the epoxy is dried, you can get rid of any excess with a putty knife. The next step is to scrub the cracked glass. If you don't clean the area correctly the residue could cause further damage to the glass. Once the glass is cleaned, use a putty knife to smooth the compound along the edges of the window and to align it with the wood frame.

Consider using a plastic cover for a more robust option. A trash bag that is heavy-duty or tarp is ideal, however you can also use masking tape to cover the glass. This will stop the crack from expanding and will also block out wind, water, bugs, and debris.

You can come up with an interim fix when you are unable reach the window in an efficient manner. Apply a small amount of silicone sealant to the edge of the broken glass. It won't completely seal the gap between frame and glass but it will help keep the break in place while you repair it.

Repainting

If your windows with glass are old, you may consider repainting them. This is a low-cost alternative to replacing windows, and can give your home a fresh new appearance. Before painting, make sure the surface is clean. Clean the window with water and soap or ruby alcohol to get rid of oil smudges as well as other residues which can hinder the paint from adhering. You should also wear rubber gloves when working on glass to avoid the risk of transferring your own oils onto the window's surface. In the end you should apply several thin coats of paint instead of one thick layer. This will allow the paint to last longer and make your windows appear smooth and even.

Make sure you have the proper tools on hand in case you want to paint glass windows. You'll require either a brush or sponge, painter's tap along with a ruler, repairer toothpicks and a ruler. You should have the brushes and paints you'll use in your kit. Follow the manufacturer's instructions. Be patient as it can take a while for the paint to completely dry.

You should also make sure the room you're working in is well ventilated if you're using solvent-based paint. This will decrease the risk of inhaling toxic chemicals, and the paint will dry more quickly. Also, make sure you have a mask to protect yourself for any spray paints that you use.

For older glass windows, it is necessary to prepare the surface prior painting. Make use of soap and warm water to thoroughly clean the glass window. Then, rub alcohol on any grease or oil residues that might hinder the paint's adhesion. Make sure the windows are completely dried before you begin to paint them.

If your glass windows are energy-efficient dual pane windows, you might be able to submit a claim to the window repairs near me company or dealer that sold them to pay any repair or replacement costs. This is particularly true if the windows are still under warranty and you've had multiple problems with condensation or damaged glass.

Sealing

There are many ways to address the issue depending on regardless of whether you have an older double glazed window repairs-pane window that has cracks in the seal, or if you own a newer insulated unit (IGU) that has experienced defogging. The most costly option is to replace the frame and insulated unit but it may be necessary if condensation or fog cause energy loss. Other alternatives include replacing the current IGU with a single-pane or repair it by drilling a small hole through the bottom of the unit and filling the solution with anti-fog.

You can also fill in the gap between the window frame and the sill or threshold by using a felt strip, vinyl v-strip, or a door sweep. Felt can be stapled, glued, or nailed into place but is not a great protection against moisture. Vinyl v-strips are easy to install and long-lasting however it can be expensive. It is generally reserved for areas exposed to abrasions that are high. Door sweeps are easy to nail to the floor and are affordable. However, they offer little or no protection between the threshold and the air.

To repair a damaged window seal, first use a putty blade to remove the old caulk. Wearing eye protection and gloves remove the glazing point -- tiny fasteners with sharp, pointed tips that pin the glass to the frame's recess. Once you have removed the glazing points, scrub the grooves and sand the wood until it is smooth. Wipe off any sanding traces and then seal the unfinished wood with a linseed oil-based paint or clear wood sealer.

Traditional glazing putty can be applied using either a putty knife or a caulking gun, however the knife is a better application that is more precise and creates a better seal. Choose a putty that is specifically designed for glass as it is more durable and stick better.

Apply a small amount the putty to the inner edge of the frame, where it meets the glass. Slide the window into the frame so that the cut line on the glass aligns with the edge of the frame. Apply pressure to the glass in order to force the putty into a solid seal. Smooth the compound using gloves and then remove any drips or caulk that were not applied correctly before it has dried.