• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Programming a Subaru Key Fob at Home

You may need the key fob to be programmed by an auto locksmith or Subaru dealer, based on how old your Subaru is. This is usually accomplished through the connection of a programming machine to the computer in the car.

To program your subaru key car, unlock the driver's door by pressing the door button and then close it. You will hear a sound on the instrument panel, and the dome lights will flash.

Step 1: Locate the Transmitter Circuit Board

There are a few different ways to program your key fob. The first step is to be aware of what kind of key fob you own. This can be done by looking at the form of the key fob or by listening to the buzz in your car.

Once you have the information you require, you can begin the process of programming your key fob at home. To accomplish this, you'll require a key made of metal and a flathead screwdriver. You can open the key fob by twisting. Then, push the metal key in and pull the battery from the small tabs that hold it in place. Replace the battery and put the case back together.

Step 2: Disconnect the key fob case

It is an ideal idea to change the batteries in key fobs in case they are not working. However, there are some situations in which the buttons inside the key fob may be damaged. If you notice that the metal contacts of the button have become loose Try soldering them into place to allow them to function again.

Before you start the process, ensure that your vehicle's doors are closed and that your ignition is turned off. You can do this by closing your driver's side door and pressing your door button ten times in rapid succession. You should then hear the instrument panel chime and your dome lights will flash. This means you're in a position to proceed.

Step 3: Insert the Key Fob in the ignition

Many websites will tell you how to program your new or Replacement Subaru Key Subaru keyfob at home. But, the majority of them do not provide very specific instructions. Reprogramming an electronic lock is best done by an expert auto dealer in Fort Bliss or a locksmith.

Sit in the driver's seat of your subaru key cutting with the engine turned off and the doors shut. Use the door button to open all doors. Open and close the driver's doors two more times. Then insert and remove the key from the ignition switch (don't turn it) 10 times in 40 seconds. The system should sound chirps to confirm that the settings have been changed.

Step 4: Turn on the ignition

Before proceeding with this method of key fob programming, it is important to note that this process only works when you have a working key already. If you don't you can find an auto-locksmith or dealer who will be required to program the key for your Subaru Fort Bliss.

Once the key has been programmed, it should be in a position to start your vehicle within a matter of five minutes. To begin, make sure all doors are shut and the engine is off. Assume a seat in the driver's chair and open all doors using the door button. Place the key in the ignition and turn it back to the first position. The electrical systems will be activated however, the engine remains in neutral. Repeat this process ten times.

Step 5: Unlock Driver's Door

Subaru offers a variety of high-end cars with key fobs which lock and unlock doors, start the engine, and even defrost windows. These devices can stop functioning.

To fix the issue then you should contact a locksmith or a dealer. This will fix the problem and make sure that your vehicle is secure.

It is necessary to first open and close the door on the driver's side. Place the key into the ignition, and then turn it to position 1. Then, you can return it to the off position. Do this ten times in an order as fast as you can. After the tenth time, you should hear a chime.

Step 6 Step 6: Press the Lock/Unlock button on the driver's Door

The process of replacing the battery on the Subaru remote key fob is very simple. Unlock the exterior fob case. Utilize a flathead tool to pry the inside of the case and take out the batteries that were in there.

After taking the battery out and replacing it with the new one. Close the case. Then, you can sit in the driver's chair and unlock all the doors using the door button control. Put the key in the ignition and turn it so that the electrical system is on, however the engine is off. Repeat this 10 times until you hear a chime from the instrument panel. This will enter the system into programming mode.

Step 7 Step 7: Press the Lock/Unlock button on the Passenger's Door

For some owners, the annoyance noise that occurs when locking and unlocking a Subaru key fob from outside the vehicle may be distracting. In certain situations you can turn off the chirp by closing and opening all doors by double-clicking the lock button on the key fob.

Close all doors, including the fuel-filler lid, and turn off the ignition. For 10 seconds then press and hold the lock button on the key fob. The instrument panel emits a chime after this is achieved. The chirp indicates that the door and fuel-filler lid are locked. The setting can also be changed so that the doors and fuel-filler lid are locked automatically, without pressing the request switch.

Step 8: Enter your 8-digit Transmitter Number

Keep the first 8 digits of the code in your head. Now, sit in your driver's seat. Close all of the doors, and turn the key to the first position (towards towards). After ten turns your instrument panel should start to sound once.

Then, you need to open the case for the key fob and locate the circuit board for the transmitter inside. The circuit board will have one or two 8-digit numbers. Take note of the sequence that starts with the first number, and follow the steps in this guide to register the code into the system of your vehicle. This process may require visiting the dealer for older models.