• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Ignition Cylinder Lock Repair

The ignition cylinder lock permits the key to be turned in order for the car to begin. It operates through springs and chambers which could be damaged by environmental conditions like low or high temperatures.

If your ignition switch or key won't turn, this could indicate that the cylinder of your lock is broken and needs to be replaced. This is a job best left to a professional auto locksmith.

Remove the Steering Column Covers

Ignition lock cylinders are mechanical components that allow keys to be put into the ignition switch and then turned to turn on the vehicle. They can fail or wear out in various ways, including keys being placed too hard or not in the correct place. They may also fail due to corrosion and other reasons. It's time to replace your ignition cylinder if it's not working. You can do this yourself, but it's a job that requires removing the covers on the steering column and the airbag cover. The process is risky and could be difficult. It may also require specialized tools for the replacement cylinder.

The ignition cylinder is situated in the middle of the column to which the steering wheel is attached. It has two screws at the bottom and an attachment clip on the side that holds it in place. It's important to remove these before you begin working on the cylinder so it doesn't fall off and get lost ignition key.

Once the screws are removed, you can take off the plastic retainers on the bottom of the cover. A metal retainer clip into the top cover to hold it in position. It is possible to remove the cover off the steering wheel to remove the tabs on the lower part of the plastic.

These can be broken off by removing one of the retaining screws, and then bending the tab a bit. If the tab is damaged completely, you can replace it with a piece perforated metal strapping available at most hardware stores. You'll require U-clips to secure the new "tab" at the bottom. These can be purchased at any automotive parts store.

After removing the tabs made of plastic and removing the airbag cover, you can reach the ignition cylinder. You can open the ignition lock with the 1/16-inch Allen wrench and pull the retaining bolt of the cylinder. You can then remove the cylinder. You may need to replace it with a specific one for an anti-theft system.

Take off the Ignition Cylinder

While many modern vehicles have transitioned to push-to-start systems, there are still a good number of cars on the road that need an ignition lock cylinder. This cylindrical, mechanical part is located inside the electrically-powered component referred to as the "ignition switch" that locks the ignition cylinder lock repair, and "reads the anti-theft code within the car key before allowing it start.

If your car is showing signs of a malfunctioning ignition lock cylinder, it may be time to contact an auto locksmith for assistance. A damaged cylinder can lead to numerous issues, including lack of power to the engine as well as problems with inserting and taking out the key. Worn keys can damage the wafer tumblers that allow for the ignition cylinder to rotate and create a blockage which prevents your car from getting started.

Based on the model and the make the cover of your ignition switch may be held on by either a clip or screw. By using a screwdriver, loosen up the screw, then slide the cover off to reveal the cylinder that locks the ignition. It is typically a metal cylinder about the size a quarter.

To take the cylinder off, you'll have to drill out the pin that holds it in place. Use a drill bit slightly larger than the slot for the key and drill through it until the cylinder breaks free. You can then remove the cylinder and then replace it.

The exact process to remove the ignition cylinder is different for each manufacturer, so it is necessary to review your service manual to find out the steps to follow. Once you have the cylinder removed, you are able to install the new ignition switch.

Before you can do this you'll have to replace the steering column covers. Two screws are required to hold the lock assembly in place. Once you've done that, installing your new ignition cylinder is likely to be fairly simple.

Take out the Ignition Switch

The ignition switch and cylinder are separate components of the electrical system inside your car ignition locked. While they may seem similar, the two can be repaired or replaced independently of one another. The switch is electrical and sends energy to your vehicle. The cylinder is a mechanical tumbler that your key slide into. You can tell if your ignition cylinder has failed due to its inability to turn the key.

When the cylinder is damaged, the tumbler's pins can wear out, making it difficult or impossible to insert or pull your key. If you notice your key is deteriorating and won't turn anymore, it's best to have the wafers in it replaced or smoothed by professional locksmiths.

The ignition cylinder is uncovered by taking off the bolt or screw depending on the make of the vehicle you're using. Consult your vehicle's manual before making the attempt at home. It can be dangerous and result in damage to the steering column or the plastic covers. Additionally, the switch is bundled with wiring for airbags and tampering with it could result in serious injury.

To remove the ignition coil, you'll need to loosen it using a drill. It is also possible to use pliers, however it's more difficult. After the ignition cylinder has been removed, you can purchase a new one from your local auto shop.

After installing the new ignition cylinder, you'll need to connect all of the wires to the electrical connections in the steering column, and then test it to ensure that it functions properly. It's best to disconnect the battery first, then disconnect the ignition key and start the engine. If the ignition is working it's time to reconnect the battery and try it again. If it doesn't work it is necessary to have the immobilizer system reset by a dealership or service technician. This is a lengthy procedure that should be left to an expert.

Install the Ignition Cylinder

The ignition switch in your car transmits an indication to the engine that it's time to get started. The key is then inserted into a lock-cylinder in order to start this process. However the pins and waxes in the cylinder can get worn out over time. It may be difficult or impossible to start your vehicle when the cylinder gets stuck.

If your car ignition lock's ignition key doesn't turn, it's likely the ignition cylinder is worn down and needs replacing. A locksmith can replace the cylinder in your ignition with a comparable one, to ensure that your key will continue to function with your existing ignition switch.

To take out the lock cylinder that was previously in use, push in on the release pin at the bottom of the assembly and lift the cylinder out of its housing. If the cylinder isn't sliding out, try pushing on the release pin again or using a screwdriver to depress an anti-rotation small button underneath the cylinder's surface. You may also try pushing in on the cylinder using your key while rotating it to the ACC or accessory position to try and push it out.

Once you've removed your old cylinder, put in the new one and turn on the vehicle to make sure whether it's functioning. If so, you can connect the trim pieces that you removed to connect to the cylinder. After that, you can begin the relearning process to connect the new keys.

Although the lock for the ignition cylinder isn't as crucial to the functionality of your car ignition switch replacement as it used to be but there are still instances where you'll require replacing it. Contact a professional like an locksmith or dealer in the automotive industry to ensure that the job is completed without damaging the steering column plastic or other components of your vehicle. It's also crucial to ensure that the new ignition cylinder is correctly coded so that your vehicle recognizes it as an authentic key. This typically requires a professional or a dealer to do this relearning.